CX2000.1 Class D 2000Wattsx1CH Product

Main Features:

Model: CX2000 2000Wx1CH

Output circuitry:Class D

Output power(RMS,≤1% THD + N@0.5 ohms):NA

Output power(RMS,≤1% THD + N@1 ohms):2000W

Output power(RMS,≤1% THD + N@2 ohms):1200W

Output power(RMS,≤1% THD + N@4 ohms):650W

Signal-to-noise (@ 1W): >90dB

Maximum power:2000W

Signal Inputs:RCA

Distortion (SMPTE-IM):NA

Amplifier Protection:YES

Input Sensitivity :0.2V-5V

Dimensions (L x W x H):53x228x453mm

TEST REPORT:

Features:

2000W rms Class-D amplifier.

1 ohm load stable.

Double Side PCB and SMD components.

Adjustable Input level, LPF, Subsonic, bass boost function, Q control.

Advanced short circuit, overload, over heat protection.

Advanced clip limit / thermal power limit function.

Easy bridgeable with same amplifier.

Optional remote controller.

3 Detailed specs:

3.1 Test Condition.ì

All the specs were tested with following condition unless noted.

1. Power supply: 14.4V DC power supply

2. Test signal: 80Hz sine wave.

3. Loads: Resistor dummy load.

4. Environment: 25 degree C, open air.

5. Relative humidity: 70%.

6. Instrument: Audio Precision SYS-2322A.

3.2 Output power performance

Following table is the RMS output power with THD+N(<22KHz) value at 5%, 3%, 2% and 1%.

Power THD+N	RMS power (1ohm)	RMS power (2ohm)	RMS power(4ohm)
5%	2000W	1350W	780W
3%	1920W	1300W	760W
2%	1900W	1260W	740W
1%	1800W	1160W	660W

Table 1Output Power with THD+N
Following chart shows the output power with THD+N curve at 4ohm loads, 2ohm loads and 1ohm loads.

Chart 1. RMS output power @4ohm with THD+N

Chart 2. RMS output power @2ohm with THD+N

Chart 3. RMS power @1ohm with THD+N

3.3 Frequency Response

1. -3dB frequency response: 13Hz~224Hz.
2. -1dB frequency response: 18Hz~175Hz.

3.4 LPF & Subsonic Filter features

LPF adjustable from 35Hz~224Hz with 24dB/Oct slope.
Subsonic Filter adjustable from 14Hz~60Hz with 24dB/Oct slope.

Chart 4.LPF response

Chart 5.Subsonic Filter response

3.5 Bass Boost Feature

Bass boost center frequency adjustable from 34Hz~90Hz, level adjustable from 0~13dB.

Chart 6.Bass boost frequency adjust(bass boost level set @ 12dB)

Chart 7.Bass boost level adjust (bass boost frequency set at 48Hz)

3.6 Bass boost Q control

Chart 9. Bass boost Q control (bass boost frequency set at 50 Hz)

1.1THD+N

THD+N=0.165% @ 375W output power with 4ohm load.

1.2Input level

0.2V~5V

1.3Signal and Noise Ratio

>75dB

1.4Protect Function

1. Overload:

Protect less than 0.8 Ohm loads at full scale output power.

2. Short Circuit:

Full rated power short circuit protect test: passed.
Full rated power long last short circuit test: 10 minutes passed.

3. Over temperature:

Limit output power while inner temperature reach 75 degree C, protect while inner temperature reach 85 degree C.

4. Low voltage:

Protect while power supply voltage lower than 8.6V.

5. Over voltage:

Protect while power supply voltage over 15.6V.

6. Power limit / Clip limit.

Clip limit while THD+N≥1%.
Power limit while inner temperature over 75 degree C.

1.5Idle current and Efficiency:

Idle current: 1.39A
Efficiency:

Load	4 OHM	2 OHM	1 OHM
Efficiency (THD+N @ 1 % )	89.6%	83.7%	76.0%

1.6Bridge method

X2000 can be bridged with same amplifier through single RCA cable, no addition switch needed. All the adjustable functions on slave amplifier will follow master once be bridged.

1.7Dimension

This amplifier’s size is at 228mmX393mmX53mm(W,L,H).